Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen angezeigt.

--- faecher:nwt:lorawan:uebersicht:lorashield:start [17.02.2020 19:49] – [IDs in den Sketch eintragen] sbel
+++ faecher:nwt:lorawan:uebersicht:lorashield:start [17.02.2020 20:19] (aktuell) – sbel
@@ Zeile 4: / Zeile 4: @@
 ===== LoraShield aufstecken =====
+{{ :faecher:nwt:lorawan:uebersicht:lorashield:img_20200217_191115.jpg?300 |}}
 ===== Bibliothek installieren =====
-Um das Shield ansprechen zu können, muss die LMIC Bibliothek installiert werden:
+Um das Shield ansprechen zu können, muss die LMIC Bibliothek installiert werden.
-{{ :faecher:nwt:lorawan:uebersicht:lorashield:lmic.png |}}
+  * [[https://github.com/matthijskooijman/arduino-lmic/archive/master.zip|Zip Datei herunterladen]] (Source: https://github.com/matthijskooijman/arduino-lmic)
+  * Installieren mit ''Sketch''-> ''Bibliothek einbinden'' -> ''ZIP-Bibliothek hinzufügen''
 ===== Sketch =====
 ++++ Klicken, um den Beispielsketch zu sehen |
-<code c hellolora.ino>
+<code c hello_lora.ino>
 // MIT License
 // https://github.com/gonzalocasas/arduino-uno-dragino-lorawan/blob/master/LICENSE
@@ Zeile 30: / Zeile 29: @@
 static const u4_t DEVADDR = 0x00000000;
-// These callbacks are only used in over-the-air activation, so they are
-// left empty here (we cannot leave them out completely unless
-// DISABLE_JOIN is set in config.h, otherwise the linker will complain).
-void os_getArtEui (u1_t* buf) { }
-void os_getDevEui (u1_t* buf) { }
-void os_getDevKey (u1_t* buf) { }
-static osjob_t sendjob;
-// Schedule TX every this many seconds (might become longer due to duty
-// cycle limitations).
-const unsigned TX_INTERVAL = 20;
-// Pin mapping Dragino Shield
-const lmic_pinmap lmic_pins = {
-    .nss = 10,
-    .rxtx = LMIC_UNUSED_PIN,
-    .rst = 9,
-    .dio = {2, 6, 7},
-};
-void onEvent (ev_t ev) {
-    if (ev == EV_TXCOMPLETE) {
-        Serial.println(F("EV_TXCOMPLETE (includes waiting for RX windows)"));
-        // Schedule next transmission
-        os_setTimedCallback(&sendjob, os_getTime()+sec2osticks(TX_INTERVAL), do_send);
-    }
-}
-void do_send(osjob_t* j){
-    // Payload to send (uplink)
-    static uint8_t message[] = "hi";
-    // Check if there is not a current TX/RX job running
-    if (LMIC.opmode & OP_TXRXPEND) {
-        Serial.println(F("OP_TXRXPEND, not sending"));
-    } else {
-        // Prepare upstream data transmission at the next possible time.
-        LMIC_setTxData2(1, message, sizeof(message)-1, 0);
-        Serial.println(F("Sending uplink packet..."));
-    }
-    // Next TX is scheduled after TX_COMPLETE event.
-}
-void setup() {
-    Serial.begin(115200);
-    Serial.println(F("Starting..."));
-    // LMIC init
-    os_init();
-    // Reset the MAC state. Session and pending data transfers will be discarded.
-    LMIC_reset();
-    // Set static session parameters.
-    LMIC_setSession (0x1, DEVADDR, NWKSKEY, APPSKEY);
-    // Disable link check validation
-    LMIC_setLinkCheckMode(0);
-    // TTN uses SF9 for its RX2 window.
-    LMIC.dn2Dr = DR_SF9;
-    // Set data rate and transmit power for uplink (note: txpow seems to be ignored by the library)
-    LMIC_setDrTxpow(DR_SF12,14);
-    // Start job
-    do_send(// MIT License
-// https://github.com/gonzalocasas/arduino-uno-dragino-lorawan/blob/master/LICENSE
-// Based on examples from https://github.com/matthijskooijman/arduino-lmic
-// Copyright (c) 2015 Thomas Telkamp and Matthijs Kooijman
-// Adaptions: Andreas Spiess
-#include <lmic.h>
-#include <hal/hal.h>
-//#include <credentials.h>
-#ifdef CREDENTIALS
-static const u1_t NWKSKEY[16] = NWKSKEY1;
-static const u1_t APPSKEY[16] = APPSKEY1;
-static const u4_t DEVADDR = DEVADDR1;
-#else
-static const u1_t NWKSKEY[16] = {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00};
-static const u1_t APPSKEY[16] = {0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00};
-static const u4_t DEVADDR = 0x00000000;
-#endif
 // These callbacks are only used in over-the-air activation, so they are
@@ Zeile 189: / Zeile 102: @@
     os_runloop_once();
 }
-&sendjob);
-}
-void loop() {
-    os_runloop_once();
-}
 </code>
 ++++
@@ Zeile 213: / Zeile 119: @@
 ===== IDs in den Sketch eintragen =====
-  * NWS: Network Session Key
+  * NWKSKEY: Network Session Key
-  * APS: Application Session Key
+  * APPSKEY: Application Session Key
+  * DEVADDR: Device Address
 {{ :faecher:nwt:lorawan:uebersicht:lorashield:keys.png |}}
+===== Kompilieren und Testen =====
+Beim Kompilieren erscheinen Warnungen, die kann man ignorieren.
+{{ :faecher:nwt:lorawan:uebersicht:lorashield:warnings.png |}}
+Wenn man den Sketch auf den Arduino lädt, sollte man bei TTN sehen, dass das Device aktiv ist:
+{{ :faecher:nwt:lorawan:uebersicht:lorashield:active.png?600 |}}
+Im Data-Tab kann man jetzt auch sehen, dass da Daten übermittelt werden:
+{{ :faecher:nwt:lorawan:uebersicht:lorashield:data.png?600 |}}